Don't throw away those worn out or broken Relton bits and
saws!
In most cases, we can repair the bit to an almost new condition for a
fraction of the cost of a new bit!
Sorry, we repair Relton products only.
Factory Service Info
• Regrind means to sharpen.
• To replace carbide, slots for carbide
inserts must still be usable.
• Remill means to cut off bit tip,
cut new slots, install new carbide, and sharpen.
• Please allow 1 - 2 weeks from our
receipt of your order for return shipment.
• Our Shipping Terms: Customer is responsible
for all shipping charges.
• Relton Corporation provides a factory
resharpening service. We do not
recommend that the user try to resharpen the tool. Authorized personnel
performing the resharpening service must use adequate eye and respiratory protection.
recommend that the user try to resharpen the tool. Authorized personnel
performing the resharpening service must use adequate eye and respiratory protection.
Relton Corporation
Authorized Factory Service Centers
|
Relton Corporation
|
|
|
317 Rolyn Place
|
|
|
Arcadia, CA 91007
|
|
|
Tel: (323) 681-2551
|
|
|
Fax: (626) 446-9671 |
| Back to top |
| Diameter | Regrind Only | Replace Carbide | Remill* | ||
|---|---|---|---|---|---|
|
Single |
Pyramid |
Single |
Pyramid |
||
|
1/4" thru 7/16" |
$4.00 |
- |
- | - | - |
|
1/2" thru 5/8" |
4.00 | $9.00 | $15.00 | $24.00 | $18.00 |
|
11/16" thru 3/4" |
5.00 | 9.00 | 15.00 | 24.00 | 19.00 |
|
27/32" |
5.00 |
- |
15.00 |
- |
19.00 |
|
7/8" thru 1" |
5.00 | 9.00 | 19.00 | 30.00 | 23.00 |
|
1-1/8" thru 1-1/4" |
6.00 | 12.00 | 27.00 | 38.00 | 33.00 |
|
1-3/8" |
6.00 | 12.00 | 27.00 | 46.00 | 34.00 |
|
1-1/2" |
7.00 | 12.00 | 32.00 | 46.00 | 38.00 |
*Note: Pyramid Point® multiple-cutter bits
can be remilled
ONLY AS SINGLE-CUTTER BITS
| Back to top | Factory Service Info |
| Diameter | Regrind | Replace Carbide & Regrind |
|---|---|---|
| 1/2" thru 11/16" |
$7.00 | $5.00 each carbide
+ $7.00 regrind |
| 3/4" thru 1-3/4" |
8.00 | 5.00 each carbide
+ 8.00 regrind |
| 1-7/8" thru 2-3/4" |
9.00 | 5.00 each carbide
+ 9.00 regrind |
| 3" thru 4" |
12.00 | 5.00 each carbide
+ 12.00 regrind |
| Porcelain Cutter Kits |
16.00 | 5.00 each carbide
+ 16.00 regrind |
| Porcelain Cutter Kit Components |
see corresponding sizes above |
see corresponding sizes above |
| All Carbide-Tipped Pilots |
4.00 | Regrind only available |
| Back to top | Factory Service Info |
| Diameter | Sharpen | Replace Carbide & Sharpen |
|---|---|---|
| 1 1/8" thru 1 3/8" |
7.00 | 5.00 each carbide
+7.00 regrind |
| 1 1/2" |
8.00 | 5.00 each carbide
+ 8.00 regrind |
| 1 5/8" thru 1 3/4" |
8.00 | 5.00 each carbide
+ 8.00 regrind |
| 2" thru 2 1/4" |
9.00 | 5.00 each carbide
+ 9.00 regrind |
| 2 1/2" thru 2 3/4" |
9.00 | 5.00 each carbide
+ 9.00 regrind |
| 3" |
10.00 | 5.00 each carbide
+ 10.00 regrind |
| 3 1/2" |
10.00 | 5.00 each carbide
+ 10.00 regrind |
| 4" |
12.00 | 5.00 each carbide
+ 12.00 regrind |
| 4 1/2" |
13.00 | 5.00 each carbide
+ 13.00 regrind |
| 5" |
14.00 | 5.00 each carbide
+ 14.00 regrind |
| Back to top | Factory Service Info |
© Copyright 2006, Relton Corporation